shared wiring

Wednesday, December 25, 2013

Simple Radio Wave Alarm

This simple circuit is sure to have the police beating a path to your door- however, it has the added advantage of alerting you to their presence even before their footsteps fall on the doormat.

Simple Radio Wave Alarm Circuit Diagram :

Notes :

The circuit transmits on Medium Wave (this is the small problem with the police). IC1a, together with a sensor (try a 20cm x 20cm sheet of tin foil) oscillates at just over 1MHz. This is modulated by an audio frequency (a continuous beep) produced by IC1b. When a hand or a foot approaches the sensor, the frequency of the transmitter (IC1a) drops appreciably.
Suppose now that the circuit transmits at 1MHz. Suppose also that your radio is tuned to a frequency just below this. The 1MHz transmission will therefore not be heard by the radio. But bring a hand or a foot near to the sensor, and the transmitters frequency will drop, and a beep will be heard from the radio.
Attach the antenna to a multiplug adapter that is plugged into the mains, and you will find that the Medium Wave transmission radiates from every wire in your house. Now place a suitably tuned Medium Wave radio near some wires or a plug point in your house, and an early-warning system is set up.
Instead of using the sheet of tin foil as the sensor, you could use a doorknob, or burglar bars. Or you could use a pushbutton and series resistor (wired in series with the 33K resistor - the pushbutton would short it out) to decrease the frequency of IC1a, so activating the system by means of a pushbutton switch. In this case, the radio would be tuned to a frequency just below that of the transmitter.

readmore...

Sunday, December 22, 2013

Funk Twang Guitar Effect Box Circuit Diagram

This is an audio effect circuit that give extra oscillation to your guitar, percussive, or semi percussive instruments, you can call it a funk box. This guitar effect circuit is basically a damped oscillator that is set slightly below its critical oscillation point.

The oscillator part is constructed by feeding back the output signal through a bandpass circuit, with the center frequency is adjusted by potentiometer R7 to add an extra “twang” , adjustable from low to high pitched timbre. Potentiometer R4 is used to adjust the gain of the oscillator, should be set to damp the oscillation at the desired decay time.

To adjust it, turn the knob slowly until a steady oscillation occurs, and turn back slightly just before it happens (the oscillation should ceases slowly). Here is the schematic diagram of the circuit.

Funk (Twang) Guitar Effect Box Circuit Diagram

readmore...

Thursday, December 19, 2013

if you have a cell phone that has a GPS on it

Most people are in great pains when they have the feelings of becoming the victim of cheating.
Be careful to go on for only professional sim car spies because there are some that are not worth your penny. Also, be careful to only use this technology for people that are subject or close to

you. The law really frowns at people who breach other peoples privacy.What good will a cell phone GPS locator do for you? You may be wondering why most smart phones today come with navigation

systems and all that. Well, it is simple, it both keeps you on track as well as it helps loved ones to know where you are at any given time. For instance, if you find yourself in a tight corner and

you cannot tell how you got there, if you have a cell phone that has a GPS on it, you can retrace your footsteps and get back on track in no time rather than going round in circles. Also, if at all

you delay and cant get home when you should, your family and friends will be able to know where you are and therefore will not worry so much.
Accessible entirely from the comfort of your own computer, cell phone spy software makes keeping tabs on your loved one simple. Installation is relatively easy as well-all you need to do is create

an information account online through their website, follow the directions, and reboot the phone. In most cases it only takes a few minutes. Once installed, youll be able to monitor the phone

immediately. There is no limit as to how much you can use the software, and there is no need for upgrades or reinstallations.
You can learn more about how to catch cheating girlfriend by reading up on reviews. These, for example, can tell you if the software in question is compatible with Blackberry phones, iPhones,

Symbian S60, Nokia, Windows Mobile, smartphones, and other mobiles on the market today. The more versatile, the better-it means that you can install the software on more than one phone. This makes

it so that if your girlfriend uses a spare, you can still see what shes up to.
Well not anymore! You can use cell phone tracking software to find out EXACTLY what she is saying to everyone she sends a text to, and shell never even know youre watching her. She wont even

know the software is installed on her phone, because it is virtually undetectable. She wont see that its installed. She wont even see that its running. And it will send all of the information

stored in her phone to a remote server, without making any noise or alerting her that its doing it.

readmore...

Monday, October 7, 2013

Digital Main Voltage Indicator

Continuous monitoring of the mains voltage is required in many applications such as manual voltage stabilisers and motor pumps. An analogue voltmeter, though cheap, has many disadvantages as it has moving parts and is sensitive to vibrations. The solidstate voltmeter circuit described here indicates the mains voltage with a resolution that is comparable to that of a general-purpose analogue voltmeter. The status of the mains voltage is available in the form of an LED bar graph. Presets VR1 through VR16 are used to set the DC voltages corresponding to the 16 voltage levels over the 50-250V range as marked on LED1 through LED16, respectively, in the figure. The LED bar graph is multiplexed from the bottom to the top with the help of ICs CD4067B (16-channel multiplexer) and CD4029B (counter).

The counter clocked by NE555 timer-based astable multivibrator generates 4-bit binary address for multiplexer-demultiplexer pair of CD4067B and CD4514B. The voltage from the wipers of presets are multiplexed by CD4067B and the output from pin 1 of CD4067B is fed to the non-inverting input of comparator A2 (half of op-amp LM358) after being buffered by A1 (the other half of IC2). The unregulated voltage sensed from rectifier output is fed to the inverting input of comparator A2. The output of comparator A2 is low until the sensed voltage is greater than the reference input applied at the non-inverting pins of comparator A2 via buffer A1.

When the sensed voltage goes below the reference voltage, the output of comparator A2 goes high. The high output from comparator A2 inhibits the decoder (CD4514) that is used to decode the output of IC4029 and drive the LEDs. This ensures that the LEDs of the bar graph are ‘on’ up to the sensed voltage-level proportional to the mains voltage.The initial adjustment of each of the presets can be done by feeding a known AC voltage through an auto-transformer and then adjusting the corresponding preset to ensure that only those LEDs that are up to the applied voltage glow.

Note.
It is advisable to use additional transformer, rectifier, filter, and regulator arrangements for obtaining a regulated supply for the functioning of the circuit so that performance of the circuit is not affected even when the mains voltage falls as low as 50V or goes as high as 280V. During Lab testing regulated 12-volt supply for circuit operation was used.)

readmore...

Friday, October 4, 2013

Watch Dog For Telephones

Most of the telephone security devices available in market are simple but quite expensive. These devices provide blinking or beeping type line-tap/misuse indications. Quite often they do not offer guaranteed protection against unauthorized operation. A very simple and unique circuit of a telephone watch-dog to safeguard subscriber telephone lines against any fraud is described here. This little circuit keeps continuous watch over the telephone lines and sounds an alarm in case of any misuse. In addition it transmits a loud tone through the telephone lines to prevent further misuse. When switch S1 is turned on, the normal (on-hook) telephone line voltage at the output of bridge-rectifier diodes D1 to D4 is approximately 48 volts, which being well above the break-down voltage of zener diode D5, the diode conducts.

As a result transistor T2 gets forward biased. This effectively grounds the base of transistor T1 which is thus cut off and the remaining circuit does not get any power supply. In this state, only a small (negligible) current is taken by the circuit, which will not affect the telephone line condition. However, when handset of any telephone connected to the telephone lines is lifted (off-hook), line voltage suddenly drops to about 10 volts. As a result, transistor T2 is switched off and transistor T1 gets forward biased via resistor R1. Now, the astable multivibrator built around timer IC1 starts oscillating and the speaker starts sounding.

Output of the astable multivibrator is also connected to the base of transistor T1 through capacitor C5. As a result, only a loud (and irritating) tone is heard in the ear-piece of the unauthorized telephone instrument. This circuit can be constructed on a veroboard using easily available low-cost components and it can be connected to any telephone line without the fear of malfunctioning. No extra power supply is required as it draws power from the telephone line for operation.

Note:

Please disconnect the gadget when you are yourself using the telephone as it cannot distinguish between authorized and unauthorized operation.

readmore...

Tuesday, October 1, 2013

Voice Bandwidth Filter

This circuit passes frequencies in the 300Hz - 3.1kHz range, as present in human speech. The circuit consists of cascaded high-pass and low-pass filters, which together form a complete band-pass filter. One half of a TL072 dual op amp (IC1a) together with two capacitors and two resistors make up a second-order Sallen-Key high-pass filter. With the values shown, the cut-off frequency (3dB point) is around 300Hz. As the op amp is powered from a single supply rail, two 10kO resistors and a 10µF decoupling capacitor are used to bias the input (pin 5) to one-half supply rail voltage.

Circuit diagram:

Voice Bandwidth Filter Circuit Diagram

The output of IC1a is fed into the second half of the op amp (IC1b), also configured as a Sallen-Key filter. However, this time a low-pass function is performed, with a cut-off frequency of about 3.1kHz. The filter component values were chosen for Butterworth response characteristics, providing maximum pass-band flatness. Overall voltage gain in the pass-band is unity (0dB), with maximum input signal level before clipping being approximately 3.5V RMS. The 560O resistor at IC1bs output provides short-circuit protection.

Author: M. Sharp - Copyright: Silicon Chip Electronics

readmore...

Saturday, September 28, 2013

Low Drop 5V Regulator

A 4-cell pack is a convenient, popular battery size. Alkaline manganese batteries are sold in retail stores in packs of four, which usually provide sufficient energy to keep battery replacement frequency at a reasonable level. Generating 5 V from four batteries is, however, a bit tricky. A fresh set of four batteries has a terminal voltage of 6.4 V, but at the end of their life, this voltage is down to 3.2 V. Therefore, the voltage needs to be stepped up or down, depending on the state of the batteries. A flyback topology with a costly, custom designed transformer could be used, but the circuit in the diagram gets around the problem by using a flying capacitor together with a second inductor.

The circuit also isolates the input from the output, allowing the output to go to 0 V during shutdown. The circuit can be divided conceptually into boost and buck sections. Inductor L1 and switch IC1 comprise the boost or step-up section, and inductor L2, diode D1 and capacitor C3 form the buck or step-down section. Capacitor C2 is charged to the input voltage, Vin, and acts as a level shift between the two sections. The switch toggles between ground and Vin+Vout , while the junction of L2, C2 and D1 toggles between –Vin and Vout +Vd1. Efficiency is directly related to the quality of the capacitors and inductors used.

Better quality capacitors are more expensive. Better quality inductors need not cost more, but normally take up more space. The Sanyo capacitors used in the prototype (C1–C3) specify a maximum ESR (effective series resistance) of 0.045 ½ and a maximum ripple current rating of 2.1 A. The inductors used specify a maximum DCR (direct current resistance) of 0.058 ½. Worst-case r.m.s. current through capacitor C2 occurs at minimum input voltage, that is, 400 mA at full load with an input voltage of 3 V.

readmore...

Wednesday, September 25, 2013

Contactless AC Mains Voltage Detector

This is a CMOS IC (CD4033) based circuit which can be used to detect presence of AC mains voltage without any electrical contact with the conductor carrying AC current/voltage. Thus it can be used to detect mains AC voltage without removing the insulation from the conductor. Just take it in the vicinity of the conductor and it would detect presence of AC voltage. If AC voltage is not present, the display would randomly show any digit (0 through 9) permanently. If mains supply is available in the conductor, the electric field would be induced into the sensing probe. Since IC used is CMOS type, its input impedance is extremely high and thus the induced voltage is sufficient to clock the counter IC. Thus display count advances rapidly from 0 to 9 and then repeats itself. This is the indication for presence of mains supply. Display stops advancing when the unit is taken away from the mains carrying conductor. For compactness, a 9-volt PP3 battery may be used for supply to the gadget.

readmore...

Sunday, September 22, 2013

Battery Charger Display Using LT1639

The Over-the-Top type of operational amplifier is ideal for use as a current sense for battery charger applications. The design described here can be used with chargers for rechargeable batteries (Lead/acid or NiCd etc). The 5 V operating supply for the circuit is derived from the battery on charge. The circuit uses a sense resistor R8 to determine the value of current ﬂowing in or out of the battery.

An LED output shows whether the battery is charging or discharging and an analogue output displays the battery charge or discharge current. The circuit can also be altered to shown different ranges of charging current to cater for higher capacity cells. IC1a and IC1b together with T1 and T2 form two current sources, which produce a voltage across R5. The voltage across R5 is proportional to the current through resistors R8 and R1 (for IC1a) or R8-R3 (for IC1b).

The current source formed by IC1a and T1 is active when the batteries are discharging and IC1b and T2 is active when the batteries are being charged. In each case the inactive opamp will have 0V at its output and the corresponding transistor will be switched off. IC1d amplifies the voltage across R5, which is proportional to the sense current. The component values given in the diagram produce an amplification factor or 10. A sense current of 0.1 A will produce an output voltage of +1 V. The supply voltage to the circuit is +5 V so this will be the maximum value that the output can achieve. This corresponds to a maximum charge/discharge current of 0.5 A To display currents from 0 to 5.0 A, resistor R7 can be omitted to give IC1d a voltage gain of 1.

Higher currents can be displayed by using a lower value of sense resistor R8. A DVM or analogue meter can be used at Vout to give a display of the charge/discharge current. The constant current sources can only function correctly when the supply to the voltage regulator circuit (UBatt. e.g. 6V or 12V) is greater than the operating voltage of the opamps (+5 V). The supply voltage to the LT1639 can be in the range of +3 V and +44V and voltages up to 40V over the supply voltage are acceptable at the inputs to the opamp. IC1c controls the charging/discharging LED output. The inputs to this opamp are connected to the outputs of the current source opamps and its output goes high when the battery is being charged and low when it is discharging.

readmore...

Tuesday, September 10, 2013

Build a18W Car Stereo Amplifier Circuit Diagram

This automobile stereo amplifier project is a class AB audio power amplifier using the Hitachi HA13118 module. It not only can be used in automobile application but also in any transportable or home amplifier process. It is simple to construct & has a maximum of outside parts. The module has a high power output from a low voltage supply using the bridge tied load system, & a high gain of 55dB.

This project will be useful in applications where the input signal is a low level, without requiring the use of a separate pre-amplifier. This IC module has a built in surge protection circuit, thermal shutdown circuit, ground fault protection circuit & power supply fault protection circuit making it reliable.

The Specifications of this project
D.C. Input : 8 – 18V at 1-2 A

Power output : 18W maximum, 4 ohm load, 18V DC supply

S/N ratio : > 70 dB

THD : < 0.2% @ 1W

Freq. Response : ~ 30 Hz to 30 kHz, –3 dB

Input level : < 25 mV, for full output (G > 50dB)

Input Impedance : ~ 30 k ohm

The supply voltage necessary for this project is 8 -18V DC, at least one to two Amps. Maximum output power will only be obtained with a power supply of 18V at greater than two A, using a four ohm speaker. The power supply ought to be well filtered to reduce mains hum, a regulated supply will reduce noise even further. Additional filtering is unnecessary if operating from a battery supply.

Circuit Diagram Description

Most of the circuitry is contained within the amplifier module. C10 is the input coupling capacitor and blocks DC from the input. C11 bypasses any RF which may be present at the input. C1 & C2 provide an AC ground for the inverting inputs of the IC. R1/C7 and R2/C8 provide a high frequency load for stability with difficult speakers. C five & C six provide bootstrap feedback for the IC. C9 & C12 provide power supply filtering.

Build a18W Car Stereo Amplifier Circuit Diagram

An externally mounted logarithmic potentiometer of between 10k ohm and 50k ohm, is used depending on the desired input impedance. The impedance ought to be keep as high as feasible for a guitar amp, unless using a separate pre-amp. Make sure-that the heat sink is mounted to the module.

readmore...

Wednesday, September 4, 2013

Simple Metal Detector Using 555 Timer

This metal detector electronic project schematic circuit is designed using a simple 555 timer integrated circuit . As you can see in the schematic circuit , this metal detector electronic project requires few external electronic parts . This circuit detects metal and also magnets.

Metal Detector with 555 Timer Circuit Daigram

When a magnet is brought close to the 10mH choke, the output frequency changes. This metal detector project can be powered from a power supply that can provide an output DC voltage between 6 an 12 volt . If a metal is closer to the L1 coil , will produce a change of output oscillation frequency, that will generate a sound in the 8 ohms speaker

readmore...

Sunday, September 1, 2013

120 VAC Lamp Dimmer

The full wave phase control circuit below was found in a RCA power circuits book from 1969. The load is placed in series with the AC line and the four diodes provide a full wave rectified voltage to the anode of a SCR. Two small signal transistors are connected in a switch configuration so that when the voltage on the 2.2uF capacitor reaches about 8 volts, the transistors will switch on and discharge the capacitor through the SCR gate causing it to begin conducting.

120 VAC Lamp Dimmer Circuit diagram

The time delay from the beginning of each half cycle to the point where the SCR switches on is controlled by the 50K resistor which adjusts the time required for the 2uF capacitor to charge to 8 volts. As the resistance is reduced, the time is reduced and the SCR will conduct earlier during each half cycle which applies a greater average voltage across the load.

With the resistance set to minimum the SCR will trigger when the voltage rises to about 40 volts or 15 degrees into the cycle. To compensate for component tollerances, the 15K resistor can be adjusted slightly so that the output voltage is near zero when the 50K pot is set to maximum. Increasing the 15K resistor will reduce the setting of the 50K pot for minimum output and visa versa. Be careful not to touch the circuit while it is connected to the AC line.

readmore...

Wednesday, August 14, 2013

Products Wiring Harnesses Harness1986 Corvette

Vehicle Wiring Products on Rbe Hlt Testers Trailer Vehicle Wiring Harness Tester

Rbe Hlt Testers Trailer Vehicle Wiring Harness Tester.

Vehicle Wiring Products on Engine Wiring Diagram 1 How To Wire A Car Engine Prestolite Wire

Vehicle Wiring Products on Engine Wiring Diagram 1 How To Wire A Car Engine Prestolite Wire

Engine Wiring Diagram 1 How To Wire A Car Engine Prestolite Wire.

Vehicle Wiring Products on Vehicle Wiring Products

Vehicle Wiring Products.

Vehicle Wiring Products on Gm Tpi Products Wiring Harnesses Tpi Harness 1986 89 Corvette

Gm Tpi Products Wiring Harnesses Tpi Harness 1986 89 Corvette.

Vehicle Wiring Products on Other Products Delfingen Industry

Other Products Delfingen Industry.

Vehicle Wiring Products on Hydrox Mobile Rus Products Vehicle Wiring Diagram

Hydrox Mobile Rus Products Vehicle Wiring Diagram.

Vehicle Wiring Products on Wiring Connections For Gm Serpentine Kit Alternators

Wiring Connections For Gm Serpentine Kit Alternators.

Vehicle Wiring Products on Split Charge Electrical Wiring Diagram

Split Charge Electrical Wiring Diagram.

Vehicle Wiring Products on Our Products Wiring Diagram 1970 76 Tecumseh Powered

Our Products Wiring Diagram 1970 76 Tecumseh Powered.

Vehicle Wiring Products on Products Accessory Equipment Light Vehicle Wiring Kit Roll Bar

Products Accessory Equipment Light Vehicle Wiring Kit Roll Bar.

readmore...

Sunday, August 11, 2013

Universal Compander Circuit diagram

Signet type NE575 compander IC is intended primarily for use with battery power supplies of 3 to 7 V (max. 8 V). Itdraws a current of 3.5 mA at 3 V and 5 mA at 7 V. The compander process (compression at the input, expansion at the output) significantly improves the signal-to-noise ratio in a communications link.

Universal Compander Circuit diagram

The IC contains two almost identical circuits, of which one (pins 1 to 9) is arranged as an expander. The other (pins 11 to 19) can be used as expander, compressor or automatic load control (ALC), depending on the externally connected circuit. For the compressor function, the inverting output of the internal summing amplifier is brought out to pin 12.

This is not the case in the expander section, where a reference voltage is available at pin 8. This pin is interlinked to pins 1 and 19 to enable the setting of the dc operating point of the op amps. The op amp in the expander section, pins 1 through 3, serves as output buffer in the compressor section, pins 17 through 19 as the input buffer. The IC has a relatively high output sensitivity and is evidently intended for processing small signals (microphone output level).

A signal of 100 mV, for instance, is amplified by 1 only. The present circuit caters to larger input signals (line level); its maximum input level is 1.5 Vrms. With a 1-V input into R13, a potential of about 500 mV exists between compressor output R7 and expander input R5. The compression characteristic is shown in Fig. 19-2 (b). The signal range is reduced by about one half at the output, which is doubled in the expander. Thus, the range after compression and expansion is the same again, but that is not necessarily the case with the input and output level. The compander can be arranged to provide a constant attenuation or amplification. With the circuit values as shown in the diagram, the input and output levels are the same.

The prototype had an overall gain of 0.5 dB when the expander input was connected directly to the compressor output. To allow acceptance of high input levels, R13, R14, and the compressor input resistance form a 10:1 attenuator. At the expander input, R5 and the expander input impedance of about 3 kfl form a potential divider. If the compander is to be used with smaller signals, the attenuation can be reduced as appropriate. If the input level lies below 100 mV, R5, R13 and R14 can be omitted. The compander covers the frequency range of 20 Hz to 20 kHz, the overall distortion is less than 1%, and the signal-to-noise ratio is about 80 dB.

readmore...

Thursday, August 8, 2013

Simple Rumble Filter Circuit Diagram

This simple rumble filter circuit diagram is a two-section active HP filter using an LM387, with a cutoff below 50 Hz at 12-dB per octave. It will help reduce rumble as a result of turntable defects in record systems.

Simple Rumble Filter Circuit Diagram

readmore...

Monday, August 5, 2013

Mobile Cellphone Battery Charger

Charging of the mobile phone battery is a huge issue while traveling as power supply source is not usually available. In case you keep your mobile phone switched on continuously, its battery will go flat within to six hours, making the mobile phone useless. A fully charged battery becomes necessary when your distance from the nearest relay station increases. Here is a simple charger that replenishes the mobile phone battery within to hours. Fundamentally, the charger is a current-limited voltage source. Usually, mobile phone battery packs need three.6-6V DC & 180-200mA current for charging. These usually contain NiCd cells, each having one.2V rating. Current of 100mA is for charging the mobile phone battery at a slow rate. A 12V battery containing eight pen cells gives sufficient current (one.8A) to charge the battery connected across the output terminals.

Diagram of cellphone charger

The circuit also monitors the voltage level of the battery. It automatically cuts off the charging system when its output terminal voltage increases above the predetermined voltage level. Timer IC NE555 is used to charge & monitor the voltage level in the battery. Control voltage pin five of IC1 is supplied with a reference voltage of five.6V by zen-er diode ZD1. Threshold pin 6 is supplied with a voltage set by VR1 & trigger pin two is supplied with a voltage set by VR2. When the discharged mobile phone battery is connected to the circuit, the voltage given to trigger pin two of IC1 is below 1/3Vcc & hence the flip-flop in the IC is switched on to take output pin three high.

When the battery is fully charged, the output terminal voltage increases the voltage at pin two of IC1 above the trigger point threshold. This switches off the flip-flop & the output goes low to terminate the charging method. Threshold pin 6 of IC1 is referenced at 2/3Vcc set by VR1. Transistor T1 is used to enhance the charging current. Value of R3 is critical in providing the necessary current for charging. With the given value of 39-ohm the charging current is around 180 mA.

The circuit can be constructed on a tiny general-purpose PCB. For calibration of cut-off voltage level, use a variable DC power source. Connect the output terminals of the circuit to the variable power supply set at 7V. Fine-tune VR1 in the middle position & slowly fine-tune VR2 until LED1 goes off, indicating low output. LED1 ought to turn on when the voltage of the variable power supply reduces below 5V. Enclose the circuit in a tiny plastic case & use suitable connector for connecting to the cell phone battery.

readmore...

Tuesday, July 30, 2013

LIGHT ALARMS

LIGHT ALARM - 1
This circuit operates when lightweight|the sunshine} Dependent Resistor receives light. When no lightweight falls on the LDR, its resistance is high and also the transistor driving the speaker isnt turned on. When lightweight falls on the LDR its resistance decreases and also the collector of the second transistor falls. This turns off the primary transistor slightly via the second 100n and also the initial 100n puts a further spike into the bottom of the second transistor. This continues till the second transistor is turned on as onerous because it will go. the primary 100n is currently nearly charged and it cannot keep the second transistor turned on. The second transistor starts to turn off and each transistors swap conditions to provide the second half of the cycle.

LIGHT ALARM - 2

This circuit is comparable to lightweight Alarm -1 however produces a louder output as a result of the speaker being connected directly to the circuit. The circuit is essentially a high-gain amplifier thats turned on initially by the LDR and then the 10n keeps the circuit turning on till it will activate no more. The circuit then starts to show off and eventually turns off utterly. the present through the LDR starts the cycle once more.

LIGHT ALARM - 3 (MOVEMENT DETECTOR)

This circuit is extremely sensitive and may be placed in a very space to detect the movement of a person up to a pair of metres from the unit.

The circuit is essentially a high-gain amplifier (made of the primary 3 transistors) that is turned on by the LDR or photo Darlington transistor. The third transistor charges the 100u via a diode and this delivers turn-on voltage for the oscillator. The LDR has equal sensitivity to the photo transistor during this circuit.

Streampoers

readmore...

Simple Voltmeter Circuit

his circuit provides a simple means to determine the voltage of a low-impedance voltage source. It works as follows. P1, which is a 1-W potentiometer, forms a voltage divider in combination with R1. The voltage at their junction is buffered by T1, and then passed to reference diode D1 via R3. D1 limits the voltage following the resistor to 2.5 V. An indicator stage consisting of T2, R4 and LED D2 is connected in parallel with D1. As long as the voltage is not limited by D1, the LED will not be fully illuminated. This is the basic operating principle of this measurement circuit.

http://www.ecircuitslab.com/2011/06/simple-voltmeter-circuit.html

readmore...

Monday, July 29, 2013

Little Door Guard

If some intruder tries to open the door of your house, this circuit sounds an alarm to alert you against the attempted intrusion. The circuit (Fig. 1) uses readily available, low-cost components. For compactness, an alkaline 12V battery is used for powering the unit. Input DC supply is further regulated to a steady DC voltage of 5V by 3-pin regulator IC 7805 (IC2).

Fig. 1: Circuit of the door guard

Assemble the unit on a general-purpose PCB as shown in Fig. 4 and mount the same on the door as shown in Fig. 3. Now mount a piece of mirror on the door frame such that it is exactly aligned with the unit. Pin configurations of IC UM3561 and transistors 2N5777 and BC547 are shown in Fig. 2.

Fig. 2: Pin configurations of UM3561 and transistors 2N5777 and BC547

Initially, when the door is closed, the infrared (IR) beam transmitted by IR LED1 is reflected (by the mirror) back to phototransistor 2N5777 (T1). The IR beam falling on phototransistor T1 reverse biases npn transistor T2 and IC1 does not get positive supply at its pin 5. As a result, no tone is produced at its output pin 3 and the loudspeaker remains silent. Resistor R1 limits the operating current for the IR LED.

When the door isopened, the absence of IR rays at phototransistor T1 forward biases npn transistor T2, which provides supply to positiveIC1. Now 3-sirensound generator IC UM3561 (IC1) gets power via resistor R5. The output of IC1 at pin 3 is amplified by Darlington-pair transistors T3 and T4 to produce the alert tone via the loudspeaker.

Fig. 3: Back view of the door assembly

Rotary switch S2 is used to select the three preprogrammed tones of IC1. IC1 produces fire engine, police and ambulance siren sounds when its pin 6 is connected to point F, P or A, respectively.

Fig. 4: Suggested enclosure with major components layout

Author : T.K. Hareendran

readmore...

Saturday, July 13, 2013

Digital Alarm Clock Using PIC

This project describes a digital clock with alarm function. It uses a PIC16F877 microcontroller to generate an accurate 1 sec delay with Timer0 using Roman’s zero error method. The time is displayed in large size font on a 4×20 character LCD that uses HD44780 display driver. You can synchronize the time with your computer time through a serial port.

Digital Alarm Clock Using PIC Circuit Diagram

The required power is provided through a 9 V wall adapter which is used to obtain a regulated +5 V power supply using a LM7805 IC. The microcontroller runs with a 20 MHz external clock. The backlight of LCD is driven by a PWM output from the microcontroller so that the back light intensity can be varied. The full software written in JAL is available to download. Source Code.

readmore...